Forum: RDM Timing Discussion
May 15th, 2014
|
Replies: 4
Views: 20,594
|
Forum: RDM Timing Discussion
May 15th, 2014
|
Replies: 4
Views: 20,594
Hi Scott,
We have been working on responders...
Hi Scott,
We have been working on responders and while doing a discovery with different RDM controllers they all come up with diffrerent numbers.
We had a test setup of 32 nodes on a network(1km...
|
Forum: RDM General Implementation Discussion
March 12th, 2014
|
Replies: 25
Views: 28,812
|
Forum: RDM General Implementation Discussion
March 11th, 2014
|
Replies: 25
Views: 28,812
Hi
Thanks for all that information.
I...
Hi
Thanks for all that information.
I have informed my management of help available. will keep let you know how we go.
While playing with it, had another question.
Does RDM support...
|
Forum: RDM General Implementation Discussion
February 16th, 2014
|
Replies: 25
Views: 28,812
Thanks Scott,
Will Do so.
Sadley We are...
Thanks Scott,
Will Do so.
Sadley We are in Australia and I dont think I be able to make in there(funds) but let see.
Will look into it.
Thanks for the advice and help.
Regards
George
|
Forum: RDM General Implementation Discussion
February 16th, 2014
|
Replies: 25
Views: 28,812
Hi Eric,
Thanks for that information.
We have...
Hi Eric,
Thanks for that information.
We have got the system to monitor the sensors, set max and min opertation temperature and also do the remaining basic information such as
Discovery,identify,...
|
Forum: RDM General Implementation Discussion
February 13th, 2014
|
Replies: 25
Views: 28,812
|
Forum: RDM General Implementation Discussion
February 5th, 2014
|
Replies: 25
Views: 28,812
|
Forum: RDM General Implementation Discussion
February 5th, 2014
|
Replies: 25
Views: 28,812
Hi,
Thanks for that information.
Would there...
Hi,
Thanks for that information.
Would there be any command which would report that a specific sensor is recoding normal operatoinal values.
most of the commands in table B-2 is to do with errors...
|
Forum: RDM General Implementation Discussion
February 3rd, 2014
|
Replies: 25
Views: 28,812
Hi Scott,
How are you?
We got the entire...
Hi Scott,
How are you?
We got the entire system working in the way of sensors.
while using the RDM controller it had the option on its user interphase which said STATUS MESSAGE.
I had hard...
|
Forum: RDM General Implementation Discussion
February 2nd, 2014
|
Replies: 25
Views: 28,812
|
Forum: RDM General Implementation Discussion
February 2nd, 2014
|
Replies: 25
Views: 28,812
|
Forum: RDM General Implementation Discussion
February 2nd, 2014
|
Replies: 25
Views: 28,812
Hi Scott,
Thanks for all that information. ...
Hi Scott,
Thanks for all that information.
we have got most of it working.
It would be great if you could guide me in how to address the sensors too.
for example?
I got 3 senesor which I...
|
Forum: RDM General Implementation Discussion
February 2nd, 2014
|
Replies: 25
Views: 28,812
Hi Scott,
Thanks for the quick reply.
I...
Hi Scott,
Thanks for the quick reply.
I am quite new to RDM. This does answer a lot of my question. Then again brought about a lot more questions :).
Please tell me if I am correct or not.
...
|
Forum: RDM General Implementation Discussion
February 2nd, 2014
|
Replies: 25
Views: 28,812
Sensor Defintion/Support Parameters
Hi,
I would like to get some support on how to define a temperature sensor using RDM.and also how to use it.(examples would be great)
Also would a RDM controller normally have a stock...
|