Forum: RDM Interpretation Questions
January 21st, 2021
|
Replies: 8
Views: 14,639
|
Forum: RDM Interpretation Questions
January 20th, 2021
|
Replies: 8
Views: 14,639
Hello,
here's a question about Split levels...
Hello,
here's a question about Split levels in Minimum level PID.
If I correctly understand about Increasing and Decreasing definitions, I infer that Increasing minimum Level has to be set...
|
Forum: DMX512 Discussion
November 8th, 2018
|
Replies: 1
Views: 7,316
BREAK timing at the receiver
Hello,
This is the my question: can a DMX receiver consider a signal low level lower than 88us as a BREAK?
If the answer in NO, this is a framing error (stop bit error): in this case may the...
|
Forum: RDM General Implementation Discussion
May 30th, 2017
|
Replies: 9
Views: 21,464
Hello everyone,
just a simple question: if I...
Hello everyone,
just a simple question: if I have implemented some Manufacturer Specific PIDs, how can I inform controller about these PIDs? I think with SUPPORTED_PARAMETERS pid.
So why on page 55...
|
Forum: RDM General Implementation Discussion
September 1st, 2016
|
Replies: 25
Views: 28,811
|
Forum: RDM Interpretation Questions
July 27th, 2016
|
Replies: 13
Views: 24,344
Hello,
In DEFAULT_SLOT_VALUE response, do I...
Hello,
In DEFAULT_SLOT_VALUE response, do I have to take into account actual personality with its footprint?
In other words, different responses depending on actual personality?
Thank you
|
Forum: RDM General Implementation Discussion
July 22nd, 2016
|
Replies: 9
Views: 16,223
|
Forum: RDM General Implementation Discussion
July 22nd, 2016
|
Replies: 9
Views: 16,223
Hello, just a simple question about Text fields...
Hello, just a simple question about Text fields use.
In CURVE_DESCRIPTION pid and similar ones, can I send a string with always 32 characters and a NULL as a terminator instead of using the actual...
|
Forum: RDM Interpretation Questions
February 9th, 2015
|
Replies: 14
Views: 24,616
Thank you,
about SOFTWARE_VERSION_LABEL it...
Thank you,
about SOFTWARE_VERSION_LABEL it is mandatory so I have to implement it in any case....about other two PIDs I agree with you.
But what is the meaning of SUPPORTED_PARAMETERS response...
|
Forum: RDM Interpretation Questions
February 5th, 2015
|
Replies: 14
Views: 24,616
About SUPPORTED_PARAMETERS pid
Hello!
I have a doubt: if I have only required parameters in my RDM implementation, do I have to respond to a GET_COMMAND SUPPORTED_PARAMETERS request from controller?
And if the answer is YES,...
|
Forum: RDM Interpretation Questions
January 29th, 2014
|
Replies: 13
Views: 23,667
Issue resolved
Hello,
Actually the issue is resolved if status messages are asserted ONLY when the condition occurs and then, once the message is collected by the controller, the responder no longer has the...
|
Forum: RDM Interpretation Questions
January 28th, 2014
|
Replies: 13
Views: 23,667
About queued messages
The issue is the third line:
- otherwise, if there are status messages at or above the requested level (see table 10-1) that have not been collected, return one or more status messages.
In...
|
Forum: RDM Interpretation Questions
January 24th, 2014
|
Replies: 13
Views: 23,667
Queued messages responses with Message Count = 0
Hello,
I need an explanation, please.
Point 10.3.1. of the standard seems to state that a receiver must always respond with a STATUS MESSAGE with PDL = 0 when it receives a GET QUEUED MESSAGE...
|