E1.20 RDM (Remote Device Management) Protocol Forums  

Go Back   E1.20 RDM (Remote Device Management) Protocol Forums > RDM User Forums > RDM User Discussion

RDM User Discussion User level discussion and questions about RDM.

Reply
 
Thread Tools Search this Thread Display Modes
Old April 15th, 2008   #1
svanciel
Junior Member
 
Join Date: Feb 2008
Location: Orlando, FL
Posts: 16
Default DMX robust - RDM not?

Not sure if this comment fits here or under user implementation but I have discovered emperically that DMX is much more robust on a compromised wiring system than the RDM traffic on the same line. A NEMA outdoor, weather rated electrical box, was found to be full of water. The wires and screw terminals on an ETC-pcb mounted on the 4-pin panel xlr were quite corroded. Yet the Aquaram power (pins 1,4) and the DMX data (pins 2,3) were able to get through and power three units and run cues correctly. However, the RDM traffic was occasionally corrupted enough to result in "Dropped Device" messages and no sensor data readings.
I'll now be going through all of the 10 year old terminal boxes to seek out other issues that may be present.

Maybe that others will make this discovery when they try to run RDM products on their "old" DMX systems that have worked well enough in the past? Might be worth noting in an implementation guide.

SteveV
svanciel is offline   Reply With Quote
Old April 15th, 2008   #2
sblair
Administrator
 
Join Date: Feb 2006
Posts: 417
Send a message via AIM to sblair Send a message via MSN to sblair
Default

Steve,

This is not surprising at all! The thing that makes DMX so forgiving is the fact that it is spitting the same packet out over and over up to 44 times/second. This masks all types of sins.

RDM by its nature is going to require a better quality infrastructure than what you were able to get away with in the past with DMX. This includes using termination and the right type of cable.

The good thing about this is that RDM will make it much easier to spot all identify and pinpoint all types of intermittent issues that previously would have resulted in random flaky behavior of the fixtures.
__________________
Scott M. Blair
RDM Protocol Forums Admin
sblair is offline   Reply With Quote
Old April 16th, 2008   #3
svanciel
Junior Member
 
Join Date: Feb 2008
Location: Orlando, FL
Posts: 16
Default

Quote:
Originally Posted by sblair
This includes using termination and the right type of cable.
True that! With the new InfoTrace Aquarams, we had to add terminators to the fourteen 4-pin lines (power supplies to heads) that never had them with the previous non-RDM units. At least all of the cable was/is the special Wybron four conductor cable, so it is still good for the power and data. Just have to go around to all of the outdoor connector boxes and look for water.

SteveV
svanciel is offline   Reply With Quote
Old May 21st, 2008   #4
derekleffew
Junior Member
 
Join Date: May 2008
Location: Las Vegas, NV, USA
Posts: 1
Default 4pin scroller terminator

Interesting. This just came up on another discussion board. I stated I'd never heard of an A4M with a 120Ω resistor between pins 2&3.

The board received the following answer:

"Ok, so the OFFICIAL response from the Wybron engineering dept is that you should terminate the power supply just like any other DMX fixture. No termination of the scrollers is necessary."
Dusty Hudgins
Sales Manager
Wybron, Inc.
719-884-6480
derekleffew is offline   Reply With Quote
Old May 22nd, 2008   #5
sblair
Administrator
 
Join Date: Feb 2006
Posts: 417
Send a message via AIM to sblair Send a message via MSN to sblair
Default

You should always terminate the end of the DMX line with 120 ohms across pins 2 & 3. This has been standard reccommened practice since the beginning with DMX512.

In some cases you could get away without doing it, but there are many times where not having proper termination will cause all kinds of nasty issues with erratic behavior.

With RDM, you MUST have the line terminated in order to work at all most of the time.
__________________
Scott M. Blair
RDM Protocol Forums Admin
sblair is offline   Reply With Quote
Old May 24th, 2008   #6
svanciel
Junior Member
 
Join Date: Feb 2008
Location: Orlando, FL
Posts: 16
Default

So, I logged in, got a welcome message, and typed a reply only to get a message that I'm NOT logged in and my message is lost.

Is there a bug in this hosting system? This has happened before.

SteveV
svanciel is offline   Reply With Quote
Old May 24th, 2008   #7
svanciel
Junior Member
 
Join Date: Feb 2008
Location: Orlando, FL
Posts: 16
Default

The prior message was an experiment. After typing it, I hit the "submit reply" button, got the "not logged in message", logged in again and the post appeared as sent. Very perplexing. Unfortunately, I still have to go back and reconstruct the original post I wanted to send.

SV
svanciel is offline   Reply With Quote
Old May 24th, 2008   #8
svanciel
Junior Member
 
Join Date: Feb 2008
Location: Orlando, FL
Posts: 16
Default

quote: "Ok, so the OFFICIAL response from the Wybron engineering dept is..."

That IS interesting because it was the Wybron reps who told me to terminate the scroller lines as we were tracking down the causes of a lot of spurious InfoTrace RDM error messages. The volume of error messages did go down when I added the 4-pin terminators from Doug Fleenor. These are not listed as a product on their web site. Perhaps they custom built these for us?

The Wybron product documentation indicates that the data protocol from the power supply to the scrollers is DMX/RDM. So, unless they have made some undocumented modifications for the ps output, it would make sense to terminate these lines just like any other DMX line. Each power supply does have its own UID. Even though very little is reported back from these, I had supposed that it was to give a warning if one should lose power. With a UID, you can identify directly (rather than indirectly as scrollers start dropping out) which ps was lost.

SteveV
svanciel is offline   Reply With Quote
Old May 24th, 2008   #9
Milton Davis
Task Group Member
 
Join Date: Aug 2006
Posts: 12
Default

Hello Steve,

The DFD 4 pin terminators are built by request. The design of the Wybron products is such that you are supposed to cable out to the first scroller, daisy chain to the nex, etc. until you get to the last one. The last open connector on the last scroller is supposed to cable back to the power supply. This serves two purposes:
1. The additional cable serves as "doubling up" of the power wires so voltage drop is better controlled.
2. There is a data terminator in the power supply so the act of connecting this loop also terminates the signal.

On those occasions when it is not practical to run the final cable from the last scroller to the power supply, a terminator can be plugged into the end of the line. While this addresses the termination issue, it leave the possability for low voltage particularly at the end of the string of scrollers. Also, just for reference, it is a 2 Watt, 120 ohm resistor connected between pins 2 and 3. We use a 2W part because a 1/4 or 1/2 Watt part might be destroyed in the event of certain connector mis-wiring configuration.

I have not gotten a good sense of the issues prompting this thread, but is is possible that the real cause of problems is one or more scrollers resetting due to a power "brown out"? Given that there is no return cable, the last units may be getting voltage "starved".

Regards,
Milton Davis, Engineer
Doug Fleenor Design, Inc.
Milton Davis is offline   Reply With Quote
Old May 24th, 2008   #10
svanciel
Junior Member
 
Join Date: Feb 2008
Location: Orlando, FL
Posts: 16
Default

Hello Milton,

I'm going to have to go back and re-read the Wybron equipment manuals (yes, I actually read them before) to hunt for the loop back wiring scheme you mentioned. This does not sound at all familiar from prior reading, discussions with Wybron reps, nor a good deal of prior scroller experience.
What I do recall is a through discussion of the "head-feet" calculations that are required in order to manage the line loss issues for power.

I understand how a loop back could be helpful to the power side of the equation, but don't recall ever, or anywhere, seeing such a recommendation for a data line, DMX or otherwise. Should I go back and re-read Recommended Practice for DMX512 as well?

The discussion basically started when I was trying to track down the cause of one set of three scrollers constantly being reported in InfoTrace as being Dropped, yet they continued to function correctly in cues. What I discovered was a NEMA wet-location rated electrical box that was full of water. The box contained a 4-pin Neutrix output jack with an ETC printed circuit board soldered to the terminals with a Euro-connector to mate up with the cable (in conduit) from the power supply. There was a lot of corrosion at this junction. Replacing the whole jack resolved the issue. My conclusion was that DMX could blast through alright but RDM suffered. Scott B essentially confirmed this.

We have other RDM error message issues. One of the suggestions from Wybron reps was to install the terminators on the scroller runs. The previous "dumb" scrollers that were in place for 8 years had worked quite well without them. We have fourteen separate runs to groups of three and four scrollers. The distances are within the head-feet requirements but it would be a major project to attempt rewiring each of these runs with a second cable to the dimmer room where the power supplies are housed. The terminators seem to have helped cut down on spurious error messages. My next project is to check and rework all of the output junctions with a more water tight junction to see if that eliminates more of the reported errors such as device dropped, initialization failure, and/or RFID read errors.

One nice feature of the Aquaram IT scrollers is a report back of the voltage and motor current values. As I recall, these readings indicate that power line loss is not a major issue but it is something I will double check.

Hope you have a nice Memorial Day weekend.
SteveV
svanciel is offline   Reply With Quote
Old May 26th, 2008   #11
Milton Davis
Task Group Member
 
Join Date: Aug 2006
Posts: 12
Default

Hello Steve,

On the return path with termination built into the power supply, perhaps I am thinking of the Chroma Q rather than the Wybron stuff. I thought the Wybron equipment followed the same practice, but I don't have it in front of me and you do.

If the scrollers are simply daisy chained with no return path or built-in termination, the 4 pin terminators are definitely a good idea. This would relate to the requirements of EIA-485 as much as DMX512.

Water + RDM = poor performance. Water + DMX512 = poor performance masked over by lots of redundant updates of the information. Is DMX more robust? Technically, no, you just can't detect the problems as easily giving the perception that the DMX signal is error free.

Regards,
Milton
Milton Davis is offline   Reply With Quote
Reply

Bookmarks

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 03:08 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.