E1.20 RDM (Remote Device Management) Protocol Forums  

Go Back   E1.20 RDM (Remote Device Management) Protocol Forums > Search Forums

Showing results 1 to 24 of 24
Search took 0.00 seconds.
Search: Posts Made By: este_
Forum: RDM User Discussion November 6th, 2017
Replies: 3
Views: 1,371
Posted By este_
We have shown a typical oscilloscope screen...

We have shown a typical oscilloscope screen showing the bus turnaround controlled by a RDM splitter (the same would be applicable to a inline booster). A generic RS 485 device would probably not be...
Forum: RDM General Implementation Discussion November 19th, 2014
Replies: 19
Views: 10,987
Posted By este_
Our responders use a automatic identify timeout:...

Our responders use a automatic identify timeout: they do not termi ate identify mode but change from LOUD mode to QUIET mode after three minutes or so to prevent "visible hanging" . Next IDENTIFY ON...
Forum: RDM General Implementation Discussion August 14th, 2014
Replies: 5
Views: 5,609
Posted By este_
Eric, you name the problem: you are talking...

Eric,

you name the problem: you are talking of fixtures, I'm not talking of fixtures at all. I am talking of multifunctional responders, such as dimmer packs, LED drivers, relays etc.

When...
Forum: RDM Interpretation Questions August 1st, 2014
Replies: 4
Views: 4,149
Posted By este_
Mostly, MINIMUM_LEVEL will go together with...

Mostly, MINIMUM_LEVEL will go together with MAXIMUM_LEVEL. When setting both, the usable fader travel will be narrowed (between the yellow dotted lines).

43

There is a simple way to widen the...
Forum: RDM General Implementation Discussion August 1st, 2014
Replies: 12
Views: 8,742
Posted By este_
Question "We would welcome your further input when the...

"We would welcome your further input when the initial draft is released for Public Review."

Any idea when this might happen?
Forum: RDM General Implementation Discussion August 1st, 2014
Replies: 5
Views: 5,609
Posted By este_
Peter, thanks for your comments which I...

Peter, thanks for your comments which I appreciate.

You're right, choosing sub-device labels to circumvent this issue is not just a workaround; as soon a sub-device is using more than one slot it...
Forum: RDM General Implementation Discussion July 13th, 2014
Replies: 0
Views: 3,366
Posted By este_
Thumbs up New PID "CURVE DEFINITION"

E1-37 allows to select curves, but does not provide any means do define user curves. It says, "Transferring user defined curve data is beyond the scope of this standard."

We have created a simple...
Forum: RDM General Implementation Discussion July 10th, 2014
Replies: 5
Views: 5,609
Posted By este_
New PID "Slot Labels"

I'd like to ask for a PID SLOT LABELS. Wie can change The device Label, but we Can not set Individual Slot labels. This may Not be of interest for a moving light, but for contactors, Protocol...
Forum: RDM Marketplace Discussion March 29th, 2014
Replies: 4
Views: 6,133
Posted By este_
The JESE Get/Set Controller covers several E1-37...

The JESE Get/Set Controller covers several E1-37 PIDs. Check www.jese.co.uk
Forum: RDM Interpretation Questions March 2nd, 2014
Replies: 4
Views: 3,981
Posted By este_
One of the the most obvious occurrences of this...

One of the the most obvious occurrences of this situation seems be the LOCK_PIN command. In this case, however, the standard (E1-37) makes it clear and says, "For devices that protect against the RDM...
Forum: RDM Interpretation Questions July 30th, 2013
Replies: 3
Views: 3,508
Posted By este_
This question relates to the BLOCK_ADDRESS issue...

This question relates to the BLOCK_ADDRESS issue raised by Hamish before.

This is my point of view:
BLOCK_ADDRESS only makes sense when there are Sub-Devices present. There is, however, no need...
Forum: RDM Marketplace Discussion June 28th, 2013
Replies: 4
Views: 6,964
Posted By este_
For These, who can't or won't do the Compiler...

For These, who can't or won't do the Compiler run: are there binaries available?
Nice Project, Anyhow.
Forum: RDM Interpretation Questions June 26th, 2013
Replies: 7
Views: 5,353
Posted By este_
I like the idea as reporting contiguous...

I like the idea as reporting contiguous sub-devices as virtual rootdevice, but then I see the problem of identifying this as "virtual" root device.

Going with Hamish' example, "Now we set the...
Forum: RDM Interpretation Questions June 13th, 2013
Replies: 14
Views: 8,073
Posted By este_
"I'm really not even sure why there should be a...

"I'm really not even sure why there should be a case you would need to NACK any of the Discovery commands." -> This might be the only way to let the controller know something was incorrectly...
Forum: RDM Interpretation Questions June 13th, 2013
Replies: 14
Views: 8,073
Posted By este_
Mute / Unmute to create a Timeout?

Thanks all for your valuable comments.

I'd like to add another issue, which was this error message:

UnMuteDeviceWithData

UnMute device info with param data.
Category: Network Management...
Forum: RDM Interpretation Questions May 6th, 2013
Replies: 14
Views: 8,073
Posted By este_
Yes, I am referring to the OLA RDM responder...

Yes, I am referring to the OLA RDM responder tests. Enclosed pls find the report for said test (file:screenshot.jpg).

Again, I object this should be rated as error. Looking at the entries of a...
Forum: RDM Interpretation Questions May 3rd, 2013
Replies: 14
Views: 8,073
Posted By este_
Filling Device Labels to 32 chars is an error?

When applying the RDM responder tests, I get an error message when filling the DEVICE_LABEL with spaces until 32 chars are reached (SET "label" will then produce a GET "label ". Since...
Forum: RDM General Implementation Discussion February 3rd, 2012
Replies: 4
Views: 6,412
Posted By este_
Thumbs up German Plugfest invitation

Next German Plugfest will take place at Friday, March 2, 2012 in Wennigsen-Steinkrug near Hannover.
More details can be obtained by email: mailto: plugfest@soundlight.de ( plugfest@soundlight.de)
Forum: RDM General Implementation Discussion August 24th, 2010
Replies: 3
Views: 5,107
Posted By este_
First German RDM Plugfest successfully launched

Leading german developers met at the SOUNDLIGHT facilities in Wennigsen, Germany. A report can be found at http://www.diereferenz.de/die-plug-fest-bilanz . The event was praised highly effective and...
Forum: RDM General Implementation Discussion July 27th, 2010
Replies: 3
Views: 5,107
Posted By este_
GERMAN RDM PLUGFEST

We're doing it! Next opportunity before PLASA would be August, 20. We invite everybody interested to come to Steinkrug/Wennigsen (Germany) and plug everything you have.

This is the official call:...
Forum: RDM General Implementation Discussion July 19th, 2010
Replies: 10
Views: 5,765
Posted By este_
furlongs/fortnight, wow! you're right,...

furlongs/fortnight, wow!

you're right, there would be unlimited possibilities. My intention was to raise some attention to this matter, and I think we got there. And,as you put it, [rpm] and [%,...
Forum: RDM General Implementation Discussion July 19th, 2010
Replies: 10
Views: 5,765
Posted By este_
Smile Displaying a fan speed can also be an intersting...

Displaying a fan speed can also be an intersting item. Every computer can do so (look into your BIOS to see the CPU fan speed), RDM devices cannot. We have fans on stage.

To display a fan speed...
Forum: RDM General Implementation Discussion July 16th, 2010
Replies: 10
Views: 5,765
Posted By este_
Eric, you're absolutely right and I agree and...

Eric,
you're absolutely right and I agree and disagree at the same time. Then, as you put it, "a percentage is unit-less because it is the ratio of two values with the same units" the mathematically...
Forum: RDM General Implementation Discussion July 15th, 2010
Replies: 10
Views: 5,765
Posted By este_
Missing RDM pararameters

I'd like to open this thread and invite everybody to make proposals for missing parameters.

One example would be: Sensors can measure anything from voltage to centigrades (see Table A-13), but...
Showing results 1 to 24 of 24

 
Forum Jump

All times are GMT -6. The time now is 02:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2019, vBulletin Solutions, Inc.