E1.20 RDM (Remote Device Management) Protocol Forums  

Go Back   E1.20 RDM (Remote Device Management) Protocol Forums > Search Forums
Reload this Page Search Results
Register FAQ Community Calendar Today's Posts Search

Showing results 1 to 12 of 12
Search took 0.00 seconds. Search: Posts Made By: majid
Forum: RDM Interpretation Questions November 2nd, 2018
Replies: 19
Views: 22,009
Posted By majid
Thanks for your complete explanations . ...

Thanks for your complete explanations
.
Great example, it clarifies the subject.
Thanks for sharing your invaluable experiences.
Forum: RDM Interpretation Questions November 2nd, 2018
Replies: 19
Views: 22,009
Posted By majid
I progressed to "Fail = 0" and "Warning = 0" on...

I progressed to "Fail = 0" and "Warning = 0" on OLA Responder Tester

my device supports GET_DEVICE_HOURS, but not SET_DEVICE_HOURS

at first I ignored SET_DEVICE_HOURS command,
and OLA warned...
Forum: RDM Interpretation Questions March 16th, 2018
Replies: 19
Views: 22,009
Posted By majid
Ok Eric I got it, I m going to fix it Maybe...

Ok Eric
I got it, I m going to fix it
Maybe save device label to eeprom gradually in background as you mentioned

Thanks
Forum: RDM Interpretation Questions March 15th, 2018
Replies: 19
Views: 22,009
Posted By majid
OK after implementing 10.3.1 I could see...

OK

after implementing 10.3.1
I could see the SET DEVICE label transaction from OLA on sniffer,

I traced the bug, it was because of short timeout of my code on receiving RDM packet, I increased...
Forum: RDM Interpretation Questions March 14th, 2018
Replies: 19
Views: 22,009
Posted By majid
Thanks Eric . You are right my code does not...

Thanks Eric
.
You are right my code does not reply when queue is empty. I need to fix it.
.
My device does not support STATUS_MESSAGE
Shall I response with STATUS_MESSAGE PDL=0 ?
.
I am...
Forum: RDM Interpretation Questions March 14th, 2018
Replies: 19
Views: 22,009
Posted By majid
thanks for reply , I also handled over size by...

thanks for reply ,
I also handled over size by responding NACK FORMAT ERROR as you said

but there is not SET DEVICE_LABEL at all from OLA (please see previous post attachment)

I think my code...
Forum: RDM Interpretation Questions March 14th, 2018
Replies: 19
Views: 22,009
Posted By majid
OLA SetOversizedDeviceLabel Fail

I have implemented Get/Set DEVICE_LABEL
It works fine with XMT-350 and ENTTEC USB PRO MK2

but during RDM responder test, OLA says "SetOversizedDeviceLabel Fail"

SET: pid: DEVICE_LABEL...
Forum: RDM Interpretation Questions December 15th, 2017
Replies: 19
Views: 22,009
Posted By majid
hmm so the responder need to be a sort of...

hmm

so the responder need to be a sort of multitasking, continue responding commands and doing previously queued commands,

but I expect controller not to ask previously queued command again...
Forum: RDM Interpretation Questions December 14th, 2017
Replies: 19
Views: 22,009
Posted By majid
I wonder if the responder response a command with...

I wonder if the responder response a command with ACK_TIMER T ms,
will the controller stop asking ALL commands during T ms ?
or the controller may ask other commands except queued command during T...
Forum: RDM Interpretation Questions December 14th, 2017
Replies: 19
Views: 22,009
Posted By majid
thread is usefull thanks. I didn't use...

thread is usefull thanks.

I didn't use ACK_TIMER at first, set address is successful but the controller (XMT-350) shows warning after setting address, I traced and found out its because of EEPROM...
Forum: RDM Interpretation Questions December 14th, 2017
Replies: 19
Views: 22,009
Posted By majid
I got it! thank you Peter

I got it!

thank you Peter
Forum: RDM Interpretation Questions December 14th, 2017
Replies: 19
Views: 22,009
Posted By majid
SET_COMMAND_RESPONSE TIMER_ACK

6.3.3 says responder shall response GET/SET command with TIMER_ACK when it takes more than 2ms to do command,
and put the response in queue after doing command

but in SET RESPONSE packet, PD is...
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT -6. The time now is 09:03 PM.

Contact Us - RDM Protocol Forums - Archive - Top

Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2024, vBulletin Solutions, Inc.